GST Library

Taxreply tweets

About GST Library

GST News

GST Calender ^{New}

E-Books

Subscription Plans

GST Case Laws

GST Notifications

GST Act / Rules

GST Rates

GST Set-off Calculator

GST Forms

Full Site Search

Classification (Chapters)

Classification (Search)

E-way Bill

Finance Bill

**NOTE :**

In this Chapter, the following expressions have the meanings hereby assigned to them:

**(a) Bars and rods**

Rolled, extruded, drawn or forged products, not in coils, which have a uniform solid cross-section along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including "flattened circles" and "modified rectangles", of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along their whole length. The thickness of such products which have a rectangular (including "modified rectangular") cross-section exceeds one-tenth of the width. The expression also covers cast or sintered products, of the same forms and dimensions, which have been subsequently worked after production (otherwise than by simple trimming or de-scaling), provided that they have not thereby assumed the character of articles or products of other headings.

**(b) Profiles**

Rolled, extruded, drawn, forged or formed products, coiled or not, of a uniform cross-section along their whole length, which do not conform to any of the definitions of bars, rods, wire, plates, sheets, strip, foil, tubes or pipes. The expression also covers cast or sintered products, of the same forms, which have been subsequently worked after production (otherwise than by simple trimming or de-scaling), provided that they have not thereby assumed the character of articles or products of other headings.

**(c) Wire**

Rolled, extruded or drawn products, in coils, which have a uniform solid cross-section along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including "flattened circles" and "modified rectangles", of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along their whole length. The thickness of such products which have a rectangular (including "modified rectangular") cross-section exceeds one-tenth of the width.

**(d) Plates, sheets, strip and foil**

Flat-surfaced products (other than the unwrought products of heading 7901), coiled or not, of solid rectangular (other than square) cross-section with or without rounded corners (including "modified rectangles" of which two opposite sides are convex arcs, the other two being straight, of equal length and parallel) of a uniform thickness, which are:

(i ) of rectangular (including square) shape with a thickness not exceeding one-tenth of the width;

(ii) of a shape other than rectangular or square, of any size, provided that they do not assume the character of articles or products of other headings.

Heading 7905, applies, inter alia, to plates, sheets, strip and foil with patterns (for example, grooves, ribs, chequers, tears, buttons, lozenges) and to such products which have been perforated, corrugated, polished or coated, provided that they do not thereby assume the character of articles or products of other headings.

**(e) Tubes and pipes**

Hollow products, coiled or not, which have a uniform cross-section with only one enclosed void along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons, and which have a uniform wall thickness. Products with a rectangular (including square), equilateral triangular or regular convex polygonal cross-section, which may have corners rounded along their whole length, are also to be considered as tubes and pipes provided the inner and outer cross-sections are concentric and have the same form and orientation. Tubes and pipes of the foregoing cross-sections may be polished, coated, bent, threaded, drilled, waisted, expanded, cone-shaped or fitted with flanges, collars or rings.

**SUB-HEADING NOTE :**

In this Chapter, the following expressions have the meanings hereby assigned to them:

(a) Zinc, not alloyed

Metal containing by weight at least 97.5% of Zinc.

(b) Zinc alloys

Metallic substances in which zinc predominates by weight over each of the other elements, provided that the total content by weight of such other elements exceeds 2.5%.

(c) Zinc dust

Dust obtained by condensation of zinc vapour, consisting of spherical particles which are finer than zinc powders. At least 80% by weight of the particles pass through a sieve with 63 micrometres (microns) mesh. It must contain at least 85% by weight of metallic zinc.

Whats new?

Cancellation of GST Registration is valid as the petitioner has failed to prove the physic..

GSTN Advisory on updates in Forms GSTR-1, GSTR-3B and Matching Offline Tool for taxpayers ..

Court accepted the petitioner's contention to unfreeze their bank account on a proposal to..

Bail application of business-woman rejected by court by ruling that vicarious liability of..

Why some of 6 digit HSNs are showing invalid on GST Portal...

High Court ordered release of goods and vehicle of petitioner in-as-much-as the interest o..

Practicing advocates should not have to face harassment to prove that they are practicing ..

Petitioner deprived of personal hearing prior to finalization of the proceedings: Orders s..